4Presser Foot Lift Lever● Lowering the presser foot lift le-ver lowers the sewing foot downonto the fabric and engages thethread tension function.✽ Wh
Before You Begin (2)Thread Cutter ButtonNoteWhen the machine stops due tojammed threads and so forth, do notstep on the foot controller, turn thepower
6Changing Needles and Light BulbNotePlease make sure power is off before carrying outthe following operations. There is a chance of injuryif the machi
2341312 Spool of Thread✽2Spool Cone HolderSpool Cap✽1Threading (1)NoteDo not move bobbin winding clutch while machineis running.Bobbin Winding1 Raise
9Manually move bobbin winding clutchback to original position.0 Cut thread and remove bobbin.7While holding the end of the thread, step onthe foot con
Quick Bobbin Thread Device1 Lift needle plate and open bob-bin door.2 Put bobbin into the bobbin case.✽ Run thread through thread notch and underlatch
10Threading (2)Note Please turn off the power before using needle threader. Accidentally stepping on the foot controller during this operation could
116 Pull thread loop to the right.Needle (HLX5) Thread#9#11#14#16#30#30#30#20#50 #60#20#20#20● The needle threader cannot beused with the thread-needl
12Stitch Samples and Needle ChartStitch Samples1 Set stitch length regulator to de-sired stitch length.2 Make sure approximately 15 cmof upper and bob
Changing Presser Feet(Zipper Foot)1 Raise presser foot, and raiseneedle to highest position.2 Loosen and remove screw usingscrewdriver.13Changing Pres
14Basic Sewing (1)Basic Sewing1 Lift foot, pull about 15 cm of upperand bobbin thread under and behindfoot, and position fabric under foot.2 Lower pre
15Basic Sewing (2)Note Make sure power is off before changing feet.Rolled Hem Foot1 Attach rolled hem foot.✽ Refer to page 13 for instructionson chan
16Basic Sewing (3)Note• Make sure power is off before changing feet.• When attaching zippers to stretch fabrics, use the pin feed methodand adjust foo
17Invisible Zipper Foot1 Attach invisible zipper foot.2 Align zipper with fabric. Mark thebase of the opening approxi-mately 2 cm above the end of the
18Quilting FootReduce the foot pressure and turnthe dial on the machine lowering thefeed dogs for free motion quilting.Walking FootForked part of oper
19Seam Guide1 Tighten the screw securely with ascrewdriver since it might other-wise loosen due to vibration.1InstallationAdjustmentTo be able to adju
20Caring for Your MachineNoteMake sure power is off beforecleaning sewing machine.1 Turn machine off.2 Remove foot.3 Remove needle plate.4 Clean out d
21Trouble Shooting✽ Before taking your sewing machine in for service, check the following chart.9-11.20Thread BreakageUpper threading is not threaded
22NOUS VOUS REMERCIONS D’AVOIR CHOISI LAMACHINE A COUDRE ELECTRONIQUE BABY LOCK.Cette machine à coudre est une des meilleures disponibles actuellement
23TABLE DES MATIÈRESAccessoires ...24Fonctions de la machine ...
“SAVE THESE INSTRUCTIONS”“This sewing machine is intended for household use.”DANGER – To reduce the risk of electric shock:● The sewing machine should
24Accessoires123456789 10111217 1821 2219 202313 14 15 16No. de pièce Désignation Code de pièce1 Couvercle XA0917-0562 Tournevis moyen XC9541-0513 Pet
25Fonctions de la machineDisque sélecteur de réglage de la pression du pied-de-biche (Page 27)Guide-fils à trois trous (Page 33)Interrupteur de la la
26Avant de commencer (1)Disque sélecteur de tension du fil● Pour augmenter la tension du fil,tourner le sélecteur de tensionvers la droite. Le fil sup
Table de rallonge pour tissuLevier de levage au genou27Levier du pied-de-biche● Abaisser le levier du pied-de-biche pour abaisser le pied sur letissu
28Avant de commencer (2)Bouton de ciseauxRemarqueSi la machine s’arrête, notamment encas de bourrage de fils, etc., ne pasappuyer sur la pédale; mette
29Remplacement de l’aiguille et de l’ampoule de lampeRemarqueBien éteindre la machine à coudre avant d’effectuerles opérations suivantes. Sinon, la ma
12 Bobine de fil✽2Broche porte-bobine coniqueCapuchon de bobine✽130Enfilage (1)RemarqueNe pas déplacer la butée de canette pendant quela machine fonc
319 A la main, ramener la butée decanette à sa position d’origine.0 Couper le fil et enlever la canette.7 Tout en tenant l’extrémité du fil,appuyer su
1 Soulever la plaque à aiguille etouvrir le volet de la canette.2Mettre la canette dans le boîtier de la canette.✽Faire passer le fil dans l’encoche p
Enfilage (2)Remarque Toujours mettre la machine hors tension avant d’utiliser l’enfileur. Une pression accidentelle sur la pédale du rhéostat pendant
FOR USERS IN THE UK, EIRE, MALTAAND CYPRUS ONLYIMPORTANT● In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carryi
6 Tirer la boucle de fil vers la droite.Aiguille (HLX5) Fil#9#11#14#16#30#30#30#20#50 #60#20#20#20● Certaines combinaisons de fil etd’aiguille ne perm
Points d’essai et tableau d’aiguillesPoints d’essai1Régler le sélecteur de longueur depoint sur la longueur de point voulue.2Vérifier qu’il y a enviro
Changement du pied-de-bicheChangement du pied-de-biche(Pied pour fermeture à glissière)1 Relever le pied-de-biche etrelever l’aiguille à la positionma
Couture de base (1)Couture de base1 Relever le pied-de-biche, sortirenviron 15 cm de fil supérieur et defil de canette et les faire passerderrière le
Couture de base (2)Remarque Bien éteindre la machine avant de changer le pied-de-biche.Pied pour ourlet rouleauté1 Fixer le pied pour ourlet rouleaut
Couture de base (3)Remarque• Bien éteindre la machine avant de changer le pied-de-biche.•Pour coudre une fermeture à glissière sur un tissu extensible
Pied pour fermeture à glissière invisible1 Fixer le pied pour fermeture àglissière invisible.2 Disposer la fermeture à glissièresur le tissu. Marquer
Pied transparent pourouatinage/matelassageRéduire la pression du pied-de-bicheet tourner le sélecteur sur la machineen abaissant les griffes d’entraîn
Guide de couture1 Serrer la vis avec un tournevissinon elle pourrait se desserreren raison des vibrations.1InstallationRéglagePour pouvoir ajuster la
Nettoyage de la machineEntretien de la machine à coudreRemarqueBien éteindre la machine avant deprocéder au nettoyage de la ma-chine à coudre.1 Eteind
CONGRATULATIONS ON CHOOSINGA BABY LOCK SEWING MACHINEYour machine is one of the finest sewing machines available for home use.To fully enjoy all the f
Dépannage✽ Avant de porter la machine à coudre à réparer, vérifier le tableau suivant.32-34.4332-34.43Utilisation incorrecte de l’enfileur automatique
ENGLISHFRENCH884-639XE8881-001Printed in Taiwan
CONTENTSAccessories ...1Machine Features ...
Accessories123456789 10111217 1821 2219 202313 14 15 161No. Part Name Part Code1 Cover XA0917-0562 Medium Screwdriver XC9541-0513 Small Screwdriver XC
2Machine FeaturesPresser Foot Pressure Adjustment Dial (Page 4)Three Hole Thread Guide (Page 10)Light Switch (Page 5)Thread TrimmerSewing Area Light (
Before You Begin (1)Power Cord and Foot ControllerNotePlease use common householdcurrent.● Plug in cord.● Plug foot controller into machine.Power Swit
Comments to this Manuals