-8-CONTROL BUTTONS & DROP FEED LEVERA.START / STOP BUTTONB.SLIDE SPEED CONTROL LEVERC.LOW SPEED BUTTOND.REVERSE STITCH BUTTONE.NEEDLE UP / DOWN BU
-9-FOOT CONTROLUse of foot control will permit control of start, stop and speed with your foot.CAUTION: To prevent accidents.1.Turn the powe
-10-STITCH SELECTION01. STRAIGHT STITCH02. LEFT POSITION, STRAIGHT STITCH03. QUILT STITCH, LIKE HAND SEWN05. STEM STITCH FOR STRETCH FABRICS04. TRIPL
-11-BOBBIN WINDINGWINDING THE BOBBINPivot spool pin into highest position.2.Pass thread from spool through thread guides as shown.3.Pull end of thread
-12-2CBA34A1INSERTING THE BOBBIN1. Place bobbin into bobbin holder with the thread unwinding counter clockwise.2. Draw thread into notch (A).3. Pul
1. Raise presser foot lever. 2. Press the needle up / down button or rotate the handwheel toward you to raise the needle into the up position. 3. P
-14- A354671234NEEDLE THREADER1.Lower the presser foot.2.Set needle in up position.3.Lower the threader slowly and draw thread through thread guide
-15-STARTING TO SEWThe machine will be set at 01 automatically to sew straight stitches when power switch is turned on.CAUTION:To prevent accidents.Wh
-16- 123451234ABAREVERSE STITCHINGReverse stitching is used for reinforcing the ends of the seams.1.Place the fabric in position where back stitching
-17-ADJUSTING THE THREAD TENSIONS453The thread tension must be properlybalanced. If adjustment is required, it can bemade by changing the upper thread
IMPORTANT SAFETY INSTRUCTIONSWhen using an electrical appliance, basic safety precautions should always be followed, including thefollowing.Read all i
-18-Type of Fabric Thread Size Needle SizeHelpful HintWhen stitches on top sideof fabric are good but bottom side tends to have a bunch of thread (as
-19-STRAIGHT STITCH SEWINGStraight stitch patterns should be selected according to the type of fabric being sewn.12STARTSTOP1.Position the fabric unde
Your machine can sew zigzag stitches of various widths and lengths by changing the settings of the stitch width and stitch length. See page 10 for c
-21-OVERCASTING-OVERLOCKING203718 06 15ACBDEUSING THE OVERCASTING FOOTCAUTION:To prevent accidents.Overcasting foot should be used for sewing patterns
-22-BLIND HEM STITCHINGThis stitch will sew without stitches showing on right side of fabric.5mm1cm5mmABRight SideWrong Side21435Wrong SideWrong SideO
-23-BUTTONHOLE SEWINGa3154261.Mark position and length of buttonhole on fabric.2.Set button on the base and slide base forward to secure button.*
-24-111222333 44567.Machine will sew the buttonhole in the order as shown and stop automatically when buttonhole is complete.CAUTION:To prevent a
-25-MULTI-STITCH ZIGZAGELASTIC STITCH SEWINGUsed for sewing on elastic band and overcaststitching on knit fabrics.Elastic stitch sewing assures you of
-26-FEED DOG CONTROLThe feed dogs control the movement of the fabric that is being sewn.They should be raised for all general sewingpurposes and lower
-1-CONTENTSMAIN PARTS2ACCESSORIES4EXTENSION TABLE / ACCESSORY STORAGE4REMOVING THE EXTENSION TABLE5OPENING THE ACCESSORY STORAGECONTENTS15CHANGING THE
-28-INSERT ZIPPERS AND PIPING 3.To insert zippers, consult the zipper package forinstructions on how to prepare zipper placket and place zipper. To s
-29-SCALLOP STITCHADJUSTING DECORATIVE PATTERNSSEWING LIGHTWEIGHT FABRICSWhen sewing lightweight fabrics, it is suggested that you use interfacing on
-30-CARING FOR YOUR MACHINE(1)(3)(4)(3)(2)A To ensure the best possible operation of your machine,it is necessary to keep the essential parts clean a
HELPFUL HINTS Machine not properly threaded. Rethread machine. 13Upper thread
Stitch Length (L) - Stitch Width (W) - LED light conversion chart in millimeters (mm) -32-010203040506StraightStraig
Stitch Length (L) - Stitch Width (W) - LED light conversion chart in millimeters (mm) StitchNo.Stitch name3-step zigzagDoubleR
Stitch Length (L) - Stitch Width (W) - LED light conversion chart in millimeters (mm) -34-StitchNo.Stitch nameL(mm)W(mm)11L(mm
Stitch Length (L) - Stitch Width (W) - LED light conversion chart in millimeters (mm) -35-DecorativeStitchNo.Cross stitchStitc
-2-MAIN PARTS134526717 16 15 14 13 121110891.Face Cover 2.Needle Up / Down button3.Reverse Stitch button4.Low speed button5.Thread cutter6.Start / Sto
-3-22232524202134283329303132373640393827264120.Carrying Handle21.Thread guide for upper threading22.Power switch23.Air vent24.Foot control plug25.Plu
-4-ACCESSORIES12354761213141 516179Some accessories are provided in the accessory case.1011 1.Needle Set 2.Bobbins 3.Spool pin cap (large) 4.Spool
-5-a. REMOVING THE EXTENSION TABLEHook your finger in the bottom of extensiontable and slide to the left. To attach, position and slide to the right.b
-6-CHANGING THE PRESSER FOOTThe presser foot must be changed according to the stitch you sew, or work you do.CAUTION:To prevent accidents.Turn OFF the
-7-CONNECTING THE MACHINEPlace the machine on a stable table.1.Connect the power cord to the machine by inserting the 2-hole plug into the plug
Comments to this Manuals