Baby Lock BL J18-QM User Manual

Model BL J18-QMwww.babylock.comConsumer Helpline: 800-264-0644Installation Guide

Pg. 95-1. To install the Belt Brackets onto your BabyLock Jewel machine, you will rst need to carefully place the machine on its side. Looking at t

Pg. 10Step 6: LCD InstallationParts Needed: 1- LCD Display 1- LCD Bracket 1- Plastic Knob6-1. Using a 5mm Allen Wrench you will remove the Jewel H

Pg. 116-7. Slip the bolt on the back of the LCD through the hole in your LCD Bracket and then secure it using the plastic knob, as shown in Fig. 6-6.

Pg. 12Step 8: Carriage to Frame AssemblyParts Needed: 1- Bottom CarriageFig. 8-2Fig. 8-3Note: Part of the long belt will already be preinstalled in y

Pg. 138-7. Now, get eye level with the under-side of the carriage, as it sits on the tracks. Conrm that your Mount Clamps line up with belt in the c

Pg. 14Step 9: Sewing Machine to Bottom Carriage AssemblyParts Needed: 1- Bottom Carriage 1- Short Belt 1- Sewing Machine9-1. Thread the belt into

Pg. 159-8. Thread the end of the belt up through the Belt Tension Housing and out the top, as shown in Fig. 9-6 and Fig. 9-7.9-9. Use the Knobs on t

Pg. 1610-3. Thread the LCD cord down the machine and attach it to the rst two (2) zip tie mounts using one (1) zip tie per mount, as shown in Fig. 1

Pg. 1710-9. Now that you have your LCD cord with the right amount of slack zip tie it to the zip tie mount, as shown in Fig. 10-11.NOTE: Keep the zi

Pg. 181. When you place your CD in the drive it should come up with this screen. Go ahead and click “Next.”2. Next the License Agreement screen comes

Pg. 1Parts Included: List AZip Ties (10)Zip Tie Mounts (7)A- Long Belt-Bottom Carriage (Pre-installed) (1)B- Short Belt-Sewing Machine (1)C- LCD Cabl

Pg. 193. Please read the Information on this screen and then click “Next.”4. We recommend you leave the installation location as is, and then click “N

Pg. 205. Please read the instructions, so you know what it is going to do, and then click “Next.”6. The default screen will come up like this and you

Pg. 217. This screen shows where the software is being installed. You can go ahead and click “Install” at this point.8. Image of installation in proc

Pg. 229. This screen tells you the installation is complete. Keep the “Launch QuiltCAD” checked and click “Finish.”10. Now go ahead and click on “Con

Pg. 2311. Next you will see this screen come up and it is not an error, just click “OK.”12. As the program is launched for the rst time, a screen ill

Pg. 2413. Please read the registration information.14. Please ll in your First Name, Last Name, and Email. Once that information is lled in you wil

Pg. 2516. This screen will then automatically come up. Please read the information and then close the internet browser window.15. Please review your

Pg. 2617. Now you will need to go to your email and open the email that is from “[email protected].” Subject line reads your email address foll

Pg. 2719. Please read the License Agreement and then click on “I have read and agree to the terms of this License Agreement,” but only if you do agree

Pg. 281. The rst time you plug your QuiltMotion into your computer you will see the screen to the right, which means you need to install some drives

Pg. 2Parts Included: List BBelt Tensioner Housing (2)Belt Clamp Back (2)Belt Clamp Front (2)M6 x 24mm Hex Bolt (4)M6 x 25mm SBHCS (2)M6 Hex Nut (8)P

Pg. 293. Select “Install from a list or specic location (Advanced)” and then click “Next.”4. Once you receive this screen you will want to click on “

Pg. 305. Start out by double click on your “C: Drive” and then “QuiltCAD.” Once in the QuiltCAD Folder you will need to select “Supt” followed by “ft

Pg. 316. Once you have the “C:\QuiltCAD\supt\ftdi” location to the left of Browse and click “Next.”7. When you receive this error go ahead and click “

Pg. 328. This screen will be shown for a few minutes, but nothing needs to be done.9. Once the installation is complete click on “Finish.”

Pg. 3311. Select “Install from a list or specic location (Advanced)” and then click “Next.”10. You will need to go through the installation steps thr

Pg. 3412. Make sure you still have the “C:\QuiltCAD\supt\ftdi” location to the left of Browse and click “Next.”13. When you receive this error go ahea

Pg. 3516. Select “Install from a list or specic location (Advanced)” and then click “Next.”15. You will need to go through the installation steps two

Pg. 3617. Make sure you still have the “C:\QuiltCAD\supt\ftdi” location to the left of Browse and click “Next.”18. When you receive this error go ahea

Pg. 3721. Select “Install from a list or specic location (Advanced)” and then click “Next.”20. You will need to go through the installation steps one

Pg. 3822. Make sure you still have the “C:\QuiltCAD\supt\ftdi” location to the left of Browse and click “Next.”23. When you receive this error go ahea

Pg. 31-2. Turn your bottom carriage upside down and make sure the front of the carriage (side with the encoder) is away from you, as shown in Fig. 1-

Pg. 41-5. Attach the two (2) Power Strip Brackets to the back of the QuiltMotion Plate by lining up these brackets under the two slots of the motor p

Pg. 51-9. Next, you will install the Power Strip to the Power Strip Bracket on your carriage. Turn your carriage upside down again and return to the

Pg. 62-4. You will leave the other end of this cable unplugged at this time.2-1. With your carriage turned upside-down, note that a ribbon cable com

Pg. 73-1. Attach one (1) Belt Clamp Front and one (1) Belt Clamp Back to one (1) Belt Bracket A using two (2) M6 x 24mm Hex Bolts and two (2) M6 Hex

Pg. 8Fig. 4-1Fig. 4-24-1. Attach one (1) Belt Tensioner Housing to one (1) Mounting Clamp using two (2) M6 x 12mm Hex Head Bolts and two (2) M6 Hex N